What are the accessories for filling industrial pumps and industrial filling pump accessories? Filling industrial pump S-valve, industrial filling pump eyeglass plate, filling industrial pump cutting ring, industrial filling pump discharge port, filling industrial pump large end bearing seat, industrial filling pump wear-resistant sleeve, filling industrial pump S-pipe long sleeve, filling industrial filling pump S-pipe short sleeve, filling industrial pump small end assembly, filling industrial pump mixing assembly, filling industrial pump swing arm, filling industrial pump swing cylinder, filling industrial pump blades, filling industrial pump piston, filling industrial pump filter element, filling industrial filling pump sealing parts, filling industrial pump bend pipe, filling industrial filling pump variable diameter pipe, filling industrial pump pipe clamp eyeglass plate, cutting ring, rubber spring, irregular nut, transition sleeve, sealing The S-pipe valve is composed of components, large and small bearings, and S-pipe welded bodies, mainly used in filling industrial pumps, With the increase in the filling height of mining paste and the strength of pumped tailings, the pumping pressure has significantly increased, making the working conditions of wear-resistant parts of tailings equipment more severe, and higher requirements have been placed on the performance of wear-resistant parts. The wear-resistant ceramic eyeglass plate cutting ring has shown obvious advantages.
In order to solve the problem of wear, two solutions were adopted in the design and manufacturing of the eyeglass plate cutting ring. The first is to use rubber springs and nuts for wear compensation, and the other is to cover the surface of the eyeglass plate cutting ring with wear-resistant ceramics.
Compensation principle: Under the pre tightening force of the unfolded nut, the rubber spring is compressed, and the cutting ring is tightly attached to the eyeglass plate. The cutting ring and the eyeglass plate belong to relative motion coupling components. After wear occurs, the rubber spring can compensate for the wear of the eyeglass plate and the cutting ring by relying on its own elasticity, eliminating the wear gap. When the wear of the cutting ring reaches a certain level, the compression of the rubber spring is zero, and there is no pressing force on the cutting ring. The nut can be tightened and unfolded to pull the S-tube welded body back and restore the compression of the rubber spring. Then, the eyeglass plate and rubber spring are compressed tightly, and the gap is compensated. This method effectively ensures the sealing performance between the eyeglass plate and the cutting ring.
Although wear compensation can extend the service life of the eyeglass plate cutting ring, due to material limitations, the amount of wear will quickly exceed the compensation range. Using wear-resistant ceramic eyeglass plate cutting rings can significantly reduce the amount of wear and reduce the number of equipment replacements.
充填工业泵配件和工业充填泵配件有哪些充填工业泵S阀、工业充填泵眼镜板、充填工业泵切割环、工业充填泵出料口、充填工业泵大端轴承座、工业充填泵耐磨套、充填工业泵S管长套、工业充填泵S管短套、充填工业泵小端总成、工业充填泵搅拌总成、充填工业泵摆臂、工业充填泵摆缸、充填工业泵叶片、工业充填泵活塞、充填工业泵滤芯、工业充填泵密封件、充填工业泵弯管、工业充填泵变径管、充填工业泵管卡 眼镜板、切割环、橡胶弹簧、异形螺母、过渡套、密封件、大小轴承和S管焊接体构成了S管阀，主要应用在充填工业泵之上，随着矿山膏体充填送高度及泵送尾砂强度的增加，造成泵送压力大幅度提高使得尾砂设备耐磨件的工况更加恶劣，对耐磨件的使用性能提高了更高的要求，耐磨陶瓷眼镜板切割环就展现出了明显优势。
为了解决磨损问题，眼镜板切割环在设计制造时采取了两种方案，第一种是利用橡胶弹簧和螺母进行磨损补偿，另一种就是在眼镜板切割环的表面覆盖耐磨陶瓷。
补偿原理：在展开螺母预紧力的作用下，橡胶弹簧受压，便切割环与眼镜板紧密贴合。切割环与眼镜板属于相对运动耦合件，产生磨损后，橡胶弹簧可依靠自身的弹性开补偿眼镜板与切割环的磨损量，消除磨损间隙。当切割环的磨损达到一定程度，橡胶弹簧压缩量为零，对切割环无压紧力，可拧紧展开螺母，将S管焊接体往后拉紧，恢复橡胶弹簧的压缩量，便眼镜板与橡胶弹簧压紧，间隙得到补偿。这种方式很好的保证了眼镜板与切割环的密封性能。
磨损补偿虽然能够延长眼镜板切割环的使用寿命，但因为材质限制，磨损量很快就会超出补偿范围，而使用耐磨陶瓷眼镜板切割环就能大幅度降低磨损量，减少设备更换次数。